|
|
 |
|
We will deduct
all shipping costs when you order 5 or more sheets of veneer. |
|
| | |
|
| |
Application
of PSA (Peel-n-Stick) Veneers Our Peel and Stick
Veneer utilizes the best quality 3M™ PSA adhesive which provides a permanent bond to most surfaces
that are smooth, dry and free of dust and contaminants.
When purchasing PSA veneer from Monster WoodShop, you can be
assured of receiving the finest face veneer backed with highest quality
3M™ PSA adhesive. |
| |
|
|
1. |
Surface preparation
Un-roll the veneer and lay sheets flat and cover with plywood
while sheets acclimatize to the ambient conditions of the job site.
This usually takes 48 hours. |
| |
|
|
2. |
Trim to Rough Size
Trim the veneer
sheet leaving it ½" oversized to allow for a final trim after the
sheet is positioned on the substrate. (Use of a sharp utility knife
or scissors is required). Loose fit the sheet with the
protective backing in place to ensure correct fit. |
| |
|
|
3. |
Remove backing
Remove the protective backing. |
| |
|
|
4. |
Apply The Veneer
Check alignment
Make sure the veneer overhangs the surface being veneered on
a 4 sides. Do not use fingers to smooth the veneer. This will
result in bubbles. "J" rollers or veneer rollers are
NOT recommended. A fiber knife or
scraper tool
is recommended to apply pressure to the sheets. |
| |
 |
Start in the center of the veneer sheet and
work out towards the edge of the sheet.
Always work in the same direction as the grain
of the veneer, paying special attention to the edges.
|
|
| |
After the veneer has been applied, trim
the remaining overhanging veneer with a sharp razor knife or x-xcto
knife, then sand the veneer edge flush with the edge of the surface. |
| |
|
|
5. |
Finish The Veneer
Adhesive should be allowed to cure for 48 hours prior to finishing.
Apply your finish promptly after cure time to protect from
moisture penetration. Most stains and finishes can be applied over PSA veneers providing you have waited long enough for he
adhesive to cure properly. Best choices of finish would be a top
coat such as a varnish or polyurethane. |
| |
|
| |
Have additional questions?
Please don't hesitate to call us TOLL FREE at
1-888-506-6678. Our office is open Monday - Friday from
9:00 a.m. to 5:00 p.m. Eastern Time. You can also take advantage
of our Online Chat: an experienced woodworker is often online, ready to
answer any questions you may have. |
| |
|
| |
Tips For Re-Facing Cabinets
With PSA Veneer |
| |
|
|
1. |
Take all items out of cabinets. |
| |
|
|
2. |
Take all of the drawers and doors and
remove all hardware from your cabinets. |
| |
|
|
3. |
Make sure all the surfaces are sound and
there is no cracking, peeling on the surfaces of your cabinets. |
| |
|
|
4. |
Repair any loose or damaged areas. Fill
in any voids wood putty, sand smooth, then seal with a topcoat finish
such as a polyurethane or varnish. It's important to let this
topcoat dry and cure properly before applying the veneer.
Depending on temperature and humidity, this could take up to1 week
Warmer temperature and lower humidity will speed up this process. |
| |
|
|
5. |
Cabinet door edges and end panels should
be veneered first. purchasing edgebanding is not always necessary, you
can cut strips off your sheet to create edgebanding. By veneering the
edges and ends first and the drawer and door faces last, you will not
see any seems when viewing the cabinets face on. |
| |
|
| |
| | |
|
|
|
 |
 |
| |
Need Faster Delivery?
Call
us with your order and we will quote you on
expedited shipping
charges. |
|
| |
