How to Fix a Dryer That Won’t Start?

Posted on

How to Fix a Dryer That Won't Start

Dryers are the most common machines in households and most of them don’t get repair due to the lack of knowledge. If you are facing a problem with your dryer and it is not working then you can follow these easy steps and solve your problem.

Here are Quick Tips on How to Fix a Dryer That Won’t Start

You may be getting many questions like why is my dryer not starting? Why is my dryer heating up but not working? So, if you want to find out the answer to all these questions then you can follow the below-mentioned steps.

The first thing that you need to do is that you need to turn off your dryer, wait for 20 to 30 minutes. After that you need to remove the plug from the outlet and put it on the floor. You can use a towel or some kind of clothes to cover the plug and keep it safe.

See also  Kenmore 80 Series Dryer Thermal Fuse (Quick Guide)

If your dryer is not starting after removing and plugging in the plug then you need to disconnect the power cable from the outlet. Once you have disconnected the power cable and reconnect it again then you can switch on the power by pressing the switch.

The next step is to find out whether the problem is with the circuit breaker or with the main board. If you have disconnected the power cable and the problem still persists then you need to check whether the power is flowing or not. If the power is not flowing then it means that the main board is damaged.

You can check if the main board is damaged by pressing the power button. If it starts working then you can replace the main board and if it is not working then you can change the fuse.

See also  How to Replace Heating Element in Samsung Dryer?

The next step is to make sure that the cord is connected properly. You can check whether the wire is loose or not by pulling it. You can also check if it is connected with the plug by turning it on and off again.

If your dryer is heating up but not starting then you need to unplug the dryer from the outlet and check if there is any kind of leak in it. If there is a leak then you can tighten it by using a screwdriver. If there is no leak then you can turn on the power by pressing the switch and check if it starts working.

FAQ

What would cause a dryer not to start?

A dryer not starting could be due to a few different reasons. First, make sure that the washer and the dryer are plugged into a working power source. If they aren’t, you’ll need to fix that before you attempt to repair the dryer. Second, check to make sure that the water level in the drum is at a minimum. Third, you should also ensure that the drum is clean, and if there’s any lint build up, you’ll have to remove it before you can repair the dryer. Finally, some dryers need a bit of time to warm up and get going, so if this is the case, you should give the dryer about 15 minutes to start before you start trying to fix it.

See also  How Long Do LG Dryers Last?

Is there a reset button on a dryer?

There is no reset button on a dryer, so you have to stop it first before you can reset it. Just hold down the switch for 2-3 seconds until the power indicator lights up, and then release the switch again. You can also press the “Start” button instead.

See also  Kenmore Elite Dryer Model 110 Heating Element - How To Replace?

Why is my dryer clicking but not turning on?

Your dryer could be clicking because the door won’t close properly. It might be stuck in the half-open position, or it might be locked in an open position. If you have a gas-powered dryer, you’ll need to check the gas valve to see if it’s not working. If you have an electric dryer, you’ll need to check your breaker to ensure that it’s not tripping. Also, make sure that there is enough power to the dryer’s heating elements.

How much does it cost to repair a dryer that won’t start?

Dryers are relatively expensive to repair. But if you have a brand new one, then you can expect to spend around $150 on labor and parts alone.

See also  How To Replace The Belt on a Dryer

How do you test a dryer start switch?

A dryer start switch is a safety feature designed to prevent electric fires. To test if it’s working properly, place a piece of paper or some fabric inside the dryer vent. If the switch turns on, then it’s fine. Otherwise, you may need to replace the switch.

Conclusion

If you are facing the same problem then don’t worry; I have mentioned the easiest steps that you can follow to fix your dryer. But if the problem still persists, then you need to call the technician and get your dryer repaired.

Leave a Reply

Your email address will not be published. Required fields are marked *