
How To Remove The Kenmore Garbage Disposal Unit Without Damaging Your Plumbing!
Kenmore is one of the most trusted brand in the washing machine market and they have been around for almost 30 years. However, when it comes to garbage disposal unit, they are not so reliable.
This is mainly because they have changed the design of their garbage disposal unit over the years. Sometimes, it becomes difficult to find a replacement part for your Kenmore washer or dryer.
Therefore, if you are having problems with your Kenmore garbage disposal, you should know how to fix it yourself.
In this post, I am going to teach you how to remove the garbage disposal unit from your Kenmore without damaging your plumbing.
What you need:
- Screw drivers
- Drill
- Wire cutters
- Hammer
1: Unscrew the four Phillips screws on the back of your garbage disposal. Make sure you don’t lose one of them.
2: Now, unscrew the two screws on the top of the disposal. Remove the metal cover and take off the rubber gasket.
3: Next, remove the two Phillips screws that hold the plastic housing. You should now have access to the gears and the motor inside the disposal.
4: Take the disposal apart and remove the three Phillips screws that are holding the gears together. Now, take off the three Phillips screws that are holding the motor together. Take care not to drop any parts.
5: Disconnect the wires from the motor. Take the motor out of the garbage disposal. Put it aside for later use.
6: Remove the two Phillips screws from the top of the disposal. Remove the metal cover and the rubber gasket.
7: Take the garbage disposal unit apart and remove the six Phillips screws that are holding the housing together. Now, remove the two Phillips screws that are holding the blade cover.
8: Take the garbage disposal apart and remove the four Phillips screws that are holding the blade assembly together. Remove the blade assembly and set it aside for later use.
9: Now, take off the two Phillips screws that hold the auger assembly together. Remove the auger assembly and set it aside for later use.
10: Turn your washer upside down and check if there is a plastic tab on the bottom of the unit. If there is a plastic tab, pull it up and out of the hole where it slides into the unit. If there isn’t a plastic tab, then you will need to cut a small circle out of the bottom of the washer. Make sure you do not cut the washer where the plastic tabs are; only cut the plastic where there are no tabs. This will make it easier to remove the washer from the disposal unit.
11: Put the washer back into the sink. Put the disposal unit back into the housing. Screw the four Phillips screws that were removed in the previous steps back into the disposal. Tighten them very firmly.
That’s it. You have just learned how to remove your garbage disposal unit without damaging your plumbing. If you have any problems with your garbage disposal, I hope you will use this tip and solve the problem yourself.
Conclusion
I am sure many of you will find this tip useful. This is because many people do not know how to fix their own appliances and they often end up calling a plumber which costs them a fortune. So, if you are facing such a problem with your garbage disposal, then try this tip. I know it will save you a lot of money.
How do you remove a garbage disposal from a sink?
First, turn off the power to the disposal. Then, find the nut in the center of the disposer’s inlet. Loosen this nut with a wrench, and then use it to pull out the disposer.
Do garbage disposals harm septic tanks?
A garbage disposal is not a good idea for homes with septic tanks because it can cause the tank to back up. As long as the garbage disposal is connected to a municipal sewer system, it should not be an issue.
Can a garbage disposal be used with a septic tank?
Garbage disposals can be used with septic tanks, but it is not recommended. The garbage disposal grinds up food and sends it through the pipes. It is possible that the food could clog the pipes and cause them to back up.
Do dishwashers have built in garbage disposals?
No, dishwashers do not have built in garbage disposals.
How do you remove an old Kenmore garbage disposal?
Remove the old disposal by turning off the power and water supply, and then unscrewing the mounting bolts that hold it to the sink. Disconnect the electrical wires from the disposal, and then remove any hoses or pipes that connect to it. Next, loosen up any clogs in the garbage disposal with a plunger. Finally, attach a new garbage disposal to your sink, turn on the power and water supply, and tighten up all of the screws.
How do you remove a garbage disposal for the first time?
Garbage disposals are installed under the sink, and they’re usually held in place by a retaining ring. There are two ways to remove a garbage disposal:
1) If the garbage disposal is mounted with screws, you’ll need a screwdriver to remove it. Loosen the screws and pull up on the disposal to remove it from the sink.
2) If the garbage disposal is mounted with a retaining ring, you’ll need to unscrew a nut or remove a washer to remove the disposal.
Can you take apart a garbage disposal?
Yes, but you should be careful. The best way to take apart a garbage disposal is with a plumber’s wrench and a screwdriver.
How do I know if my garbage disposal is stuck?
If your garbage disposal is stuck, you will usually notice it because there will be a loud noise coming from it whenever you turn on the sink. If it isn’t making any noise, then it is probably not jammed. Instead, it is probably just clogged. In that case, you should try to unclog it yourself. If you don’t succeed, then you should call a professional to do it for you.