How to Replace The Belt on a Maytag Dryer?

Posted on

Doing your own home repairs can be a great way to save money and time. Replacing the belt on a Maytag dryer is one of those simple repairs that many homeowners can do themselves. This article will explain step-by-step how to replace a broken or worn out belt on a Maytag dryer, including what tools you may need for the job and how to safely disconnect the power supply before beginning.

Removing Access Panels & Drum

Removing Access Panels & Drum is an important part of the process when replacing a belt on a Maytag dryer. This step requires the user to access the rear of the dryer and take off either the lower access panel, or remove the front drum. Both require a few simple steps to be taken prior to beginning work on replacing the belt.

See also  GE Front Load Dryer Belt Replacement - How To Choose

The first task in removing access panels & drum should be to unplug your dryer from its power source before attempting any repairs. Then locate either one of two screws that secure your lower access panel, remove them with a Phillips-head screwdriver and slide out the panel. The second option is removing your front drum by opening up your lint filter door, releasing two roller wheels at each corner of top edge and gently pulling forward until it can be removed from its installed position.

Locating & Replacing the Old Belt

When it comes to doing your own repairs around the house, there’s no better appliance than a Maytag dryer. But when the belt on your Maytag dryer begins to wear out, replacing it can be a challenge. Luckily for DIYers and home repair enthusiasts, replacing the belt in a Maytag dryer is not as difficult as you may think. Here’s a guide on how to locate and replace an old belt in your Maytag Dryer.

See also  How to Find Out If You Have a Gas Dryer?

The first step is finding where the old belt is located inside the machine. To do this, remove the back panel of your dryer with a screwdriver and look at the motor pulley system to identify which part holds the drive belt. Once you have identified where the belt is located, use pliers or needle-nose pliers to remove it from its place within the machine.

Installing New Belt & Repositioning Drum

Installing a new belt and repositioning the drum on a Maytag dryer is an easy, do-it-yourself project that can be completed in just a few steps. In order to replace the belt, begin by unplugging your dryer and removing the two screws holding the access panel in place. Once you have done this, slide the existing belt off of the motor pulley located at the back of your machine.

See also  Maytag Steam Clean Dishwasher

Then, slide on your newly purchased replacement belt and make sure it is properly positioned around both pulleys – being careful not to stretch or twist it along its full length. Finally, with some gentle pushing, carefully reposition the drum inside of your dryer so that it sits properly atop its rollers before reattaching and locking down your access panel. Within minutes you will have successfully installed a new belt onto your Maytag Dryer!

See also  Kenmore Elite Dryer Model 110 Heating Element - How To Replace?

Reassembling the Dryer

One of the most essential tasks is reassembling the dryer after replacing the belt. The process involves unhooking and removing various parts from inside the dryer, so make sure to wear protective glasses throughout. Start by disconnecting all wires from each component within the machine before unscrewing any nuts or bolts that are keeping them in place.

After taking out any components that need to be replaced, such as rollers and pulleys, secure them back into their places using screws and/or bolts. Finally, reconnect all wires back into their original positions before carefully inserting and aligning your newly installed belt around them.

Testing the New Belt

Once you have successfully installed the new belt, it is important to run a test in order to ensure that it works properly. Start by turning on your dryer and watching carefully while it heats up. If the belt is still on its place and no longer slips, you’ll know that your new belt is in working condition.

See also  Kenmore Dryer Heating Element Replace

Leave a Reply

Your email address will not be published. Required fields are marked *